If you don’t know how to cut the molding, read this article. We offer you detailed instructions about how to cut quarter round with miter saw. Let’s see!

You are completing a room but don’t know how to handle pieces of quarter rounds. Or the moldings in your child’s room could fall off.

You don’t know how to handle the situation. Here we provide detailed steps to cut a quarter round with a miter saw. (read more best miter saw under 200 buying guide here)

• Step 1. Select some pieces of quarter round
• Step 2. Measure the length of the quarter round
• Step 3. Choose the correct cutting angle and cutting direction
• Step 4. Proceed to cut the quarter round
• Step 5. Check with the wall for a snug fit
• Step 6. Sanding
• Step 7. Apply glue
• Step 8. Shoot the fixed nail
• Step 9. Check for gaps, if any

Let’s read on to learn!

How To Cut Quarter Round With Miter Saw?

This project is not a difficult job. Just follow the steps below, and you can easily pass.

However, there are a few tools you need to prepare before you get started:

• Some pieces of quarter round (molding).
• Sharpened pencil.
• Miter box and hand/miter saw.
• Gloves, masks, and eyeglasses.

Step 1. Select some pieces of quarter round

The first step is the most basic but also very important. Usually, quarter-round pieces are 240 cm long. The longer piece is 490 cm long.

You can measure the front wall step length to choose the right length quarter round pieces. It will avoid you having to join or cut multiple times.

In our experience, it is more common to use an 8-foot quarter round for a room at home. Longer pieces are suitable for large spaces such as big offices or meeting rooms.

Step 2. Measure the length of the quarter round

Place the quarter round on the wall and use a pencil to mark the position you want to saw. Please put it as close to the wall and floor base as possible to avoid errors in the cutting process.

Now you can easily mark the distance to cut with a pencil. Draw a quarter arc in the shape of the previous quarter round.

Step 3. Choose the correct cutting angle and cutting direction

Typically, each end of a quarter round will end in a door jamb or corner. The most standard and most suitable parameter for quarter-round cutting angle is 45 degrees.

The two-quarter rounds need to fit together perfectly to match perfect round corners. Simply cut two pieces of the quarter round in the same direction and at a 45-degree angle.

Unaffected by the design difference, the angles will always be 90 degrees. The simplest way for this task is to use a 90-degree protractor to measure. Then you just need to split them in half, and you’ve determined the correct cutting angle.

Similarly, if the angle is not 90 degrees, you can also determine the cut angle by bisecting the original angle.

Step 4. Proceed to cut the quarter round

First, use the pins to determine the position of the quarter round relative to the saw. Let’s fix a quarter round with a non-dominant hand. Use your other hand (dominant hand) to adjust the saw.

Apply a suitable force to the saw on the molding. Move the saw through the quarter round a few times until the quarter round is “ripped” apart.

In this step, you can use the miter box to support your mission. It’s available at most hardware stores, or you can order it online.

Don’t forget to wear gloves, a dust mask, and eye protection to protect your health during the cutting process. You need to focus 100% to make sure the cut is correct and avoid unfortunate accidents.

Step 5. Check with the wall for a snug fit

After you have finished cutting, try placing the quarter round you just cut on the wall to see if it fits. If it is too long, you should shorten it by cutting it to work best.

If the quarter round does not meet the entire length of the wall, join the two pieces together.

Step 6. Sanding

Use sandpaper to tip the molding. Sandpaper should have a roughness of 200 grit.

Step 7. Apply glue

First, spread a layer of construction glue over the quarter-round section. You then place the molding on the base of the wall along the perpendicular face.

Press the molding firmly so that it fits snugly against the base of the wall. You then hold that state for about 30 seconds.

Step 8. Shoot the fixed nail

Gluing alone is not enough. You need to use nails to secure the molding to the baseboard.

Step 9. Check for gaps, if any

The last thing is to check if everything fits together or not. Wrong cutting angles will lead to an excess or a shortage of molding.

The best way to cover blemishes is to use rubber glue to protect them. You can then paint over those imperfections.

Final Thoughts

Quarter-round or molding is to fill in gaps or defects between the floor and baseboard. In addition, it also helps to increase the aesthetics of your home.

The knowledge on how to cut a quarter round with a miter saw hopefully will help you somewhat when you want to repair your small house yourself.

Referring source: https://geariz.com